Drawing a BLANK DFI MoBo

HigHTecHReDNecK · 26-June-08, 12:42 AM

HELP !!!!

I'm trying to set up a DFI Lanparty NF4 SLi Expert w/ 3500+ Sempron 2gb Kingston ram ( two sticks )

I can get to bios , but if I change ANYTHING I get a blank screen after hitting F10 to save and exit. I clear the bios and it works again. I'm rying to get it to boot from CD but it keeps going to the hard drive and saying incert boot disk .

Any ideals , I've tryed all kinds of different ram , both SATA and IDE hard drives , Different optical drive ........

Master Yunk · 26-June-08, 12:49 AM

Flash to new/old bios?

HigHTecHReDNecK · 26-June-08, 01:04 AM

Thanks , yup just did , and then wiped the drive on a different rig so it was unallocated space , its working now

Dont know if it was the BIOS or wiping the drive , but thanks for the advice

EDIT: NVM it started installing windows , but as soon as it went through and rebooted , blank screen again

EDIT 2 : Reset BIOS yet again and now its going through part two of the OS install ?!?!? I hope i dont have to reset the BIOS every time I power down , I'm tryin to set this up for some Sempron O/Cing

Sn0wMan · 26-June-08, 08:00 AM

Try the DFI NF4LD329 BIOS. It has proven to be one of the best for overall stability. You should be able to find it online. I have it but you have to flash from within windows.

Good luck!

HigHTecHReDNecK · 26-June-08, 01:15 PM

I'll give that a shot Snowman thanks. I did manage to get it running , but only after I swapped the proc out ? I think the proc is bad.........

26-June-08, 12:42 AM		#1 (permalink)
HigHTecHReDNecK Sophist'Hoe"cated ReDNecK Reviewer	Drawing a BLANK DFI MoBo HELP !!!! I'm trying to set up a DFI Lanparty NF4 SLi Expert w/ 3500+ Sempron 2gb Kingston ram ( two sticks ) I can get to bios , but if I change ANYTHING I get a blank screen after hitting F10 to save and exit. I clear the bios and it works again. I'm rying to get it to boot from CD but it keeps going to the hard drive and saying incert boot disk . Any ideals , I've tryed all kinds of different ram , both SATA and IDE hard drives , Different optical drive ........

26-June-08, 12:49 AM		#2 (permalink)
Master Yunk D.O.A. Tournament Champion	Re: Drawing a BLANK DFI MoBo Flash to new/old bios?

26-June-08, 01:04 AM		#3 (permalink)
HigHTecHReDNecK Sophist'Hoe"cated ReDNecK Reviewer	Re: Drawing a BLANK DFI MoBo Thanks , yup just did , and then wiped the drive on a different rig so it was unallocated space , its working now Dont know if it was the BIOS or wiping the drive , but thanks for the advice EDIT: NVM it started installing windows , but as soon as it went through and rebooted , blank screen again EDIT 2 : Reset BIOS yet again and now its going through part two of the OS install ?!?!? I hope i dont have to reset the BIOS every time I power down , I'm tryin to set this up for some Sempron O/Cing Last edited by HigHTecHReDNecK; 26-June-08 at 02:40 AM..

26-June-08, 08:00 AM		#4 (permalink)
Sn0wMan Apex Tech Demi-God	Re: Drawing a BLANK DFI MoBo Try the DFI NF4LD329 BIOS. It has proven to be one of the best for overall stability. You should be able to find it online. I have it but you have to flash from within windows. Good luck!

26-June-08, 01:15 PM		#5 (permalink)
HigHTecHReDNecK Sophist'Hoe"cated ReDNecK Reviewer	Re: Drawing a BLANK DFI MoBo I'll give that a shot Snowman thanks. I did manage to get it running , but only after I swapped the proc out ? I think the proc is bad.........

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Need a concept drawing for your project?	mnpctech	Case Modding	0	08-June-08 10:52 AM
drawing request,	computerman	Graphics / Media	4	16-November-06 02:39 PM
Converting to a line drawing	DickNervous	Graphics / Media	6	28-April-06 11:08 AM
Drawing 7.9A on an 18A PSU...safe?	DJ Blur	Extreme Cooling	4	10-August-05 09:12 PM
3D drawing program?	Dimazz	Graphics / Media	6	03-September-04 09:54 PM