Video Card Water Block

Fahye · 16-November-05, 08:17 PM

I was wondering if any place has made a video card coller with moveable 1/2 nozzels because Im getting a 7800GT and I would like to add it to my water system but the way everything is set up if I connect it from the rad ==> video card block using a dangerden on like the nv78 the tubing would bend.

Post me if you guys would Like a pic of what Im talking about.

Albedo · 16-November-05, 09:28 PM

Bending in tubes isn't a bad thing, really. If you have to, use some FrozenCPU CoolSleeves to prevent kinking.

Fahye · 16-November-05, 09:50 PM

does it really help because its a real big turn it goes proable a 98 give or take degree bend.

lAnonymousl · 16-November-05, 09:55 PM

Not sure I follow....you were planning to have all your tubing straight? How many elbows are we talking?

Fahye · 16-November-05, 10:46 PM

theres no elbows right now on the water cooling system
what IM saying theres a rad on the front bottom of the case and right now and its connected on the back outake where there is a rad
Im getting a NV78 (thinking about it). And if I get that thing it would go between the 2 rads. But connect it from the front rad it would make a 90degree bend but I think elbows would be good. Because my tube that connect the A8N chipset block to the front rad is also making a bend to where over time its going to kink would a elbow fit on the A8N and a NV78
I just don't know if DD makes elbows for there products.

Edited it.

Enko · 16-November-05, 11:42 PM

kind of hard to follow your post since the puncutation was few and far between . ..

Fahye · 17-November-05, 01:29 AM

I edit it so you guys might be able to under stand

its this huge economics project got my head spinning
really hard to run your own business with staff and all

16-November-05, 08:17 PM		#1 (permalink)
Fahye Apex Master Tech	Video Card Water Block I was wondering if any place has made a video card coller with moveable 1/2 nozzels because Im getting a 7800GT and I would like to add it to my water system but the way everything is set up if I connect it from the rad ==> video card block using a dangerden on like the nv78 the tubing would bend. Post me if you guys would Like a pic of what Im talking about.

16-November-05, 10:46 PM		#5 (permalink)
Fahye Apex Master Tech	theres no elbows right now on the water cooling system what IM saying theres a rad on the front bottom of the case and right now and its connected on the back outake where there is a rad Im getting a NV78 (thinking about it). And if I get that thing it would go between the 2 rads. But connect it from the front rad it would make a 90degree bend but I think elbows would be good. Because my tube that connect the A8N chipset block to the front rad is also making a bend to where over time its going to kink would a elbow fit on the A8N and a NV78 I just don't know if DD makes elbows for there products. Edited it. Last edited by Fahye; 17-November-05 at 12:51 AM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FrozenCPU // Zalman ZM-GWB2 Low Profile Video Card Water Block w/ RAM Sinks (10 / 9 / 8mm ID)	Gizmo	Vendor News RSS	0	12-October-05 03:58 PM
FrozenCPU // Danger Den NV-78 SLI Copper 3/8" ID Video Card Water Block Kit (nVidia 7800)	Gizmo	Vendor News RSS	0	01-October-05 03:53 PM
FrozenCPU // Danger Den NV-78 SLI Copper 1/2" ID Video Card Water Block Kit (nVidia 7800)	Gizmo	Vendor News RSS	0	01-October-05 03:53 PM
FrozenCPU // Danger Den NV-78 Video Card Water Block (nVidia 7800) - 3/8" Barbs	Gizmo	Vendor News RSS	0	21-September-05 03:51 PM
FrozenCPU // Danger Den NV-78 Video Card Water Block (nVidia 7800) - 1/2" Barbs	Gizmo	Vendor News RSS	0	21-September-05 03:51 PM

16-November-05, 09:28 PM		#2 (permalink)
Albedo Apex Tech Fanatic Supreme	Bending in tubes isn't a bad thing, really. If you have to, use some FrozenCPU CoolSleeves to prevent kinking.

16-November-05, 09:50 PM		#3 (permalink)
Fahye Apex Master Tech	does it really help because its a real big turn it goes proable a 98 give or take degree bend.

16-November-05, 09:55 PM		#4 (permalink)
lAnonymousl The Who? Hoe	Not sure I follow....you were planning to have all your tubing straight? How many elbows are we talking?

16-November-05, 11:42 PM		#6 (permalink)
Enko Apex Tech God	kind of hard to follow your post since the puncutation was few and far between . ..

17-November-05, 01:29 AM		#7 (permalink)
Fahye Apex Master Tech	I edit it so you guys might be able to under stand its this huge economics project got my head spinning really hard to run your own business with staff and all