Gpu Cascade

JSU · 08-February-05, 01:01 AM

Here are some pics of the gpu cascade i put together tonight. it was a gpu dd unit (tuned) until a couple hours ago. now its a gpu cascade.

please dont judge me on this one, it was thrown together pretty darn quickly
excuse the blurry pics

$SOLID$ Necro · 08-February-05, 03:08 AM

Have you gotten any temps out of it yet?

What are you going to be using it on?

JSU · 08-February-05, 12:15 PM

Iam going to be using it on my 9600xt iyh. I havnt realy started it up as acascade so not temps yet.

JSU · 09-February-05, 12:01 AM

I was at -80c but the system started going crazy before completely equalizing, turn out there is a area in the cap tube that was bent too much and had a leak. its fixed and i am evacing now.

$SOLID$ Necro · 09-February-05, 02:46 AM

Are you Cryo cooling the Ram chips too?

J/K..are you going to add any ram sinks, or V-Mod the card?

JSU · 09-February-05, 03:49 AM

Pics

, it was idling around -82c

btw i lost one of those screws to the baker gpu block, anyone know where i can get one (or 2

)???? Its a realy pain

the card is being vmodded and i dont think ill need ram sinks (the whole card will be below ambient iyh)

$SOLID$ Necro · 09-February-05, 04:59 AM

Baker block screws

What is so special about them?

If Zenn hadn't shown me one of those a few weeks back, I wouldn't have known what the hell you were talking about!

There aren't many sub zero "Chillin" Pimps around here at the moment, you are one of a few around here who have built there own, and I don't think any of them are anywhere near those temps (Other than Zenn)

This phase will change very soon...

I know of at least 3 peeps standing in line for a custom made one from you know who

BTW..what clocks have you hit with it so far? I had one on air that did pretty well at 550+ core and 350+ memory all stock.

JSU · 09-February-05, 10:54 AM

well i cant realy remember what clocks ive hit with the xt seing as i played with it for a day and then sent it out. it did pretty well though. the 9600pro has awsome memory its doing around 500/400 max with frags on stock cooling and ramsinks (its a bit unstable at those clocks but i havnt realy fooled around witth the voltage.)

JSU · 09-February-05, 05:28 PM

I insulated today. I had it at -74c~ under load but something is wrong with the chagre (i played with it again) and its not holding the laod very well

snocrossgjd · 09-February-05, 07:36 PM

Dude those temps are impressice i thought my 33c was cool but damn -120.4 degrees thats insane

JSU · 09-February-05, 09:10 PM

yup, thanks!

JSU · 09-February-05, 11:54 PM

im done playing with co2, waiting for ethylene now. I have to add a desuperheater and hp cutoff.

ZENNZZO · 10-February-05, 02:32 AM

Very nicely done Bro...you are always impressing me with your projects, and that is a hard thing to do 'round here...Keep up the dam fine work and remember you can never forget the desuperheater and hp cutoff.LMAO...

JSU · 11-February-05, 03:44 AM

http://img24.exs.cx/img24/33/head17qi.jpg

$SOLID$ Necro · 11-February-05, 05:21 AM

OOOOH! Time to make some snow cones!

I like mine ATI red if you don't mind

JSU · 11-February-05, 01:06 PM

lol

well this was suppose to be posted yesterday

Well i added 3 things today, expansion tank, desuper heater and a hp cutoff. The expansion tank allows me to have something like 70psi static pressure

(preolly more when i turn off the firt stage) the desuperheater gives me a real easy startup, before it was toooo taxing ont he first stage and sometimes wouldnt start correctly. hp cutoff- i can leave it alone for a while

while testing.

temperary fan on the desuperheater

JSU · 29-July-05, 08:51 PM

Well the thing holding me back from -100c on this unit was this tedious job, but its done now....

Highperf15 · 29-July-05, 08:59 PM

Damn.........I'm just in complete awe............now will a CPU run at that temp???

JSU · 29-July-05, 09:04 PM

this one is actulay for my gpu but yeah. those temps were on co2 and i have much colder/easier to use stuff now

. are you talking about under load? or are you asking if a cpu wil operate at those temps? the answer to both is yes though i think loaded cpu will be like -85c~

BigAkita · 29-July-05, 09:16 PM

I would like you to explain the origin and development of that system.

08-February-05, 01:01 AM		#1 (permalink)
JSU Coolie-Hoe	Gpu Cascade Here are some pics of the gpu cascade i put together tonight. it was a gpu dd unit (tuned) until a couple hours ago. now its a gpu cascade. please dont judge me on this one, it was thrown together pretty darn quickly excuse the blurry pics

09-February-05, 04:59 AM		#7 (permalink)
$SOLID$ Necro Mastah Overclocker	Baker block screws What is so special about them? If Zenn hadn't shown me one of those a few weeks back, I wouldn't have known what the hell you were talking about! There aren't many sub zero "Chillin" Pimps around here at the moment, you are one of a few around here who have built there own, and I don't think any of them are anywhere near those temps (Other than Zenn) This phase will change very soon... I know of at least 3 peeps standing in line for a custom made one from you know who BTW..what clocks have you hit with it so far? I had one on air that did pretty well at 550+ core and 350+ memory all stock. Last edited by $SOLID$ Necro; 09-February-05 at 05:06 AM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Cascade CPU Water Block.	painfull	Extreme Cooling	3	04-February-06 03:19 AM
My Cascade * 56k Beware!!! *	JSU	Extreme Cooling	68	01-August-05 10:57 PM
What is cascade cooling?	RavingNutsack	Other OC Hardware/Software	2	12-March-05 08:32 PM
What is a cascade?	JSU	Extreme Cooling	9	01-March-05 07:17 PM
Cascade XXX	Gamma_Goblin	Extreme Cooling	0	31-March-04 02:47 AM

08-February-05, 03:08 AM		#2 (permalink)
$SOLID$ Necro Mastah Overclocker	Have you gotten any temps out of it yet? What are you going to be using it on?

08-February-05, 12:15 PM		#3 (permalink)
JSU Coolie-Hoe	Iam going to be using it on my 9600xt iyh. I havnt realy started it up as acascade so not temps yet.

09-February-05, 12:01 AM		#4 (permalink)
JSU Coolie-Hoe	I was at -80c but the system started going crazy before completely equalizing, turn out there is a area in the cap tube that was bent too much and had a leak. its fixed and i am evacing now.

09-February-05, 02:46 AM		#5 (permalink)
$SOLID$ Necro Mastah Overclocker	Are you Cryo cooling the Ram chips too? J/K..are you going to add any ram sinks, or V-Mod the card?

09-February-05, 03:49 AM		#6 (permalink)
JSU Coolie-Hoe	Pics , it was idling around -82c btw i lost one of those screws to the baker gpu block, anyone know where i can get one (or 2 )???? Its a realy pain the card is being vmodded and i dont think ill need ram sinks (the whole card will be below ambient iyh)

09-February-05, 10:54 AM		#8 (permalink)
JSU Coolie-Hoe	well i cant realy remember what clocks ive hit with the xt seing as i played with it for a day and then sent it out. it did pretty well though. the 9600pro has awsome memory its doing around 500/400 max with frags on stock cooling and ramsinks (its a bit unstable at those clocks but i havnt realy fooled around witth the voltage.)

09-February-05, 05:28 PM		#9 (permalink)
JSU Coolie-Hoe	I insulated today. I had it at -74c~ under load but something is wrong with the chagre (i played with it again) and its not holding the laod very well

09-February-05, 07:36 PM		#10 (permalink)
snocrossgjd Apex Techie Wannabe	Dude those temps are impressice i thought my 33c was cool but damn -120.4 degrees thats insane

09-February-05, 09:10 PM		#11 (permalink)
JSU Coolie-Hoe	yup, thanks!

09-February-05, 11:54 PM		#12 (permalink)
JSU Coolie-Hoe	im done playing with co2, waiting for ethylene now. I have to add a desuperheater and hp cutoff.

10-February-05, 02:32 AM		#13 (permalink)
ZENNZZO Direct Cool Hoe	Very nicely done Bro...you are always impressing me with your projects, and that is a hard thing to do 'round here...Keep up the dam fine work and remember you can never forget the desuperheater and hp cutoff.LMAO...

11-February-05, 03:44 AM		#14 (permalink)
JSU Coolie-Hoe	http://img24.exs.cx/img24/33/head17qi.jpg

11-February-05, 05:21 AM		#15 (permalink)
$SOLID$ Necro Mastah Overclocker	OOOOH! Time to make some snow cones! I like mine ATI red if you don't mind

11-February-05, 01:06 PM		#16 (permalink)
JSU Coolie-Hoe	lol well this was suppose to be posted yesterday Well i added 3 things today, expansion tank, desuper heater and a hp cutoff. The expansion tank allows me to have something like 70psi static pressure (preolly more when i turn off the firt stage) the desuperheater gives me a real easy startup, before it was toooo taxing ont he first stage and sometimes wouldnt start correctly. hp cutoff- i can leave it alone for a while while testing. temperary fan on the desuperheater

29-July-05, 08:51 PM		#17 (permalink)
JSU Coolie-Hoe	Well the thing holding me back from -100c on this unit was this tedious job, but its done now....

29-July-05, 08:59 PM		#18 (permalink)
Highperf15 a.k.a., Frank Bullitt	Damn.........I'm just in complete awe............now will a CPU run at that temp???

29-July-05, 09:04 PM		#19 (permalink)
JSU Coolie-Hoe	this one is actulay for my gpu but yeah. those temps were on co2 and i have much colder/easier to use stuff now . are you talking about under load? or are you asking if a cpu wil operate at those temps? the answer to both is yes though i think loaded cpu will be like -85c~

29-July-05, 09:16 PM		#20 (permalink)
BigAkita n00b-ass reviewer	I would like you to explain the origin and development of that system.