The pots
















05:



Futuremark - ORB - Project Comparison

03:

Futuremark - ORB - Project Comparison

01:

Futuremark - ORB - Project Comparison

AM3:



The Setup:

CPU: X6800 @ 5ghz 1.95v -130C
Cooling: Ironmods Sumo XL LN2 pot
GPU: EVGA 8800GTX single card stock air 650/1100
RAM: 1gb Geil PC2 9600
HDD: WD Raptor
PSU: PCP&C 750watt Silencer
Case: DangerDen Torture Rack

Special thanks to: Ton, Chris, Jacob, DangerDen gang, EVGA.

Nice stuff buddy. Is that a newer design? If so do you plan on selling them also?

Yea newer design. I am goign to try to get 6 made up.

Quote: Originally Posted by Cpt.Planet Yea newer design. I am goign to try to get 6 made up.

Copper ones?


I was going to buy a chilly1 copper one, but if you are making copper now, I'd be more than happy to get one of these.

With all that ice, did you have any condensation issues?

Quote: Originally Posted by s1ugh34d Copper ones? I was going to buy a chilly1 copper one, but if you are making copper now, I'd be more than happy to get one of these. With all that ice, did you have any condensation issues?

Yea I am gonna get 6 copper made up. Chilly1 no longer is making pots. Hell he cant even finish a phase unit. Hes about 2 years backed up on those. The only guys making pots in the US are MickeyMouse, K|ngP|n, and myself really.

No issues what so ever ran for over 4 hours with no problems. It was a little more humid here then i would have liked but my insulation job held up just fine.

1.95v poor CPU.

Great Work Cpt.Planet. Gotta Luv those scores :-)

Quote: Originally Posted by Zaltan 1.95v poor CPU.

she was happy at -130C

Quote: Originally Posted by Cpt.Planet Yea I am gonna get 6 copper made up. Chilly1 no longer is making pots. Hell he cant even finish a phase unit. Hes about 2 years backed up on those. The only guys making pots in the US are MickeyMouse, K|ngP|n, and myself really. No issues what so ever ran for over 4 hours with no problems. It was a little more humid here then i would have liked but my insulation job held up just fine.

In four hours how much LN2 did you use?

Is it easier to insulate with the taipered bottom?

I'll take one, most definately, just PM me when you have them done.

Tappered bottom just means a few more sheets of insulation. Makes it easier to get a good mount as well. I used around 10-15 liters maybe a little less

I would think the tapered bottom helps with insulation...

It would give the area around the socket something a bit beefier to push down into as far as closed cell foam...and the angle cut into the pot give the water a path to run that does condensate that it has to run into something that will soak it before the board attracts it. Unlike the previous revision..

This is a good design bro.
Now just tighten up all the other standards in your small manufacturing process like holes drilled on center on brackets etc....and you have gold on your hands here...
Looking forward to seeing more.

Keep up the good work
Digi

Yea unfortunately I had to make all the hold downs on the last ones last minute. I had worked out getting them made and the guy left me at the last second.

Quote: Originally Posted by Cpt.Planet Tappered bottom just means a few more sheets of insulation. Makes it easier to get a good mount as well. I used around 10-15 liters maybe a little less

Awesome work dude. But see, that is the one problem I always had with LN2 cooling. 15 litres in 4 hours. And since that pot doesn't hold that much, I am assuming you had to keep adding to it. Would be hell if you were playing CoD2 or somethings. It's great for benchmarking, but that's it.

Now, if you could figure a way to setup a closed loop......

-159 c , im gettin cold just thinkin bout that temp.

Great work Cpt. and love the slick look of them pots!!!!!!!

Quote: Originally Posted by HigHTecHReDNecK -159 c , im gettin cold just thinkin bout that temp. Great work Cpt. and love the slick look of them pots!!!!!!!

Thanks Mace your really helping me out big time. I appreciate it.

Quote: Originally Posted by Cpt.Planet Yea unfortunately I had to make all the hold downs on the last ones last minute. I had worked out getting them made and the guy left me at the last second.

I understood that...

I just know for the quality you shoot for...and the crowd you shoot for...the hardcore enthusiast...
It makes sense to get tight quality control when making such an impressive product.

These look pimp....

Keep up that work and I may just buy one of them....lol

Quote: Originally Posted by Cpt.Planet Thanks Mace your really helping me out big time. I appreciate it.

I'm sending Mace that last pot you sent me. That should keep him busy
til your new ones are made :-)

Thank you Mace for making the hold downs again. You really are the man. I am trying to get around 6 more copper pots made up within the next 2 months let me know if anybody wants one.

Quote: Originally Posted by Cpt.Planet Thank you Mace for making the hold downs again. You really are the man. I am trying to get around 6 more copper pots made up within the next 2 months let me know if anybody wants one.

Dibs

10 char

Man, this stuff is amazing I don't know very much about overclocking and all of the extreme cooling techniques you use, but I can sure spot hard work and an attention to detail when I see it. And those numbers just blow my mind! Very nice work Cpt., as well as anyone else helping you out