Custom Case Window

Lazy8s · 31-December-02, 03:24 PM

Hey, I'm looking at buying and pimping out my first case. I am looking at the silver aluminum version of the Thermaltake Xaser II (the A6000A). I was gonna get it with a solid side and make my own custom window. How hard is it to make a custom window in an aluminum case? Is this a good case? And lastly, where should I go to get the supplies for a custom window? Thx in advance.

Wixx · 31-December-02, 06:52 PM

Custom windows are easy to implement in any case. All you'll need is a sheet of plexiglass or Lexan, something to cut it with (I recommend a table or chop saw, although Dremels do work if you have the patience), and then something to attach it to the side panel. Some people use glue, some people use tape or velcro, some use moulding, but I've always been a fan of aluminum pop rivets myself. These supplies can be found at most hardware stores or a big place like Home Depot.

Lokie · 31-December-02, 07:07 PM

I use silicon(clear) to stick my window,flexible and sturdy.
Just remember safety, and allways check your measurements.....TWICE.
A jigsaw,scrollsaw,or roto tool to cut your design.
Alum is easy to cut just make sure you mask off what you don't want scratched up.
Take your Time don't rush it.
And if you can practice using wich tool to get the feel for how it works.

piscikeeper · 31-December-02, 09:41 PM

to make it a little easier on the finish,try cutting from the inside.slips are easier to cover if they can't be seen at all.

Tom10167 · 03-January-03, 08:09 AM

Yes, I look forward to an aluminium case just because it is so much easier to cut and work with.

31-December-02, 03:24 PM		#1 (permalink)
Lazy8s Apex Techie Lite	Custom Case Window Hey, I'm looking at buying and pimping out my first case. I am looking at the silver aluminum version of the Thermaltake Xaser II (the A6000A). I was gonna get it with a solid side and make my own custom window. How hard is it to make a custom window in an aluminum case? Is this a good case? And lastly, where should I go to get the supplies for a custom window? Thx in advance.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Lokie's Custom Window Etching Technique	GlitterKill	PC Apex Review / Article Feedback	43	07-February-05 06:59 AM
Custom window...	BlackFox	Case Modding	12	10-August-03 09:55 PM
places that do custom window etchings	squishy	Case Modding	1	27-May-03 10:32 PM
Custom Window Help!!!	Digital-World	Case Modding	3	10-October-02 01:42 AM
Custom Window Etchings	Sk8forMaple	Case Modding	18	24-September-02 11:19 AM

31-December-02, 06:52 PM		#2 (permalink)
Wixx Modd-God	Custom windows are easy to implement in any case. All you'll need is a sheet of plexiglass or Lexan, something to cut it with (I recommend a table or chop saw, although Dremels do work if you have the patience), and then something to attach it to the side panel. Some people use glue, some people use tape or velcro, some use moulding, but I've always been a fan of aluminum pop rivets myself. These supplies can be found at most hardware stores or a big place like Home Depot.

31-December-02, 07:07 PM		#3 (permalink)
Lokie Custom What?	I use silicon(clear) to stick my window,flexible and sturdy. Just remember safety, and allways check your measurements.....TWICE. A jigsaw,scrollsaw,or roto tool to cut your design. Alum is easy to cut just make sure you mask off what you don't want scratched up. Take your Time don't rush it. And if you can practice using wich tool to get the feel for how it works.

31-December-02, 09:41 PM		#4 (permalink)
piscikeeper Apex Tech Fanatic	to make it a little easier on the finish,try cutting from the inside.slips are easier to cover if they can't be seen at all.

03-January-03, 08:09 AM		#5 (permalink)
Tom10167 Apex Tech Maniac	Yes, I look forward to an aluminium case just because it is so much easier to cut and work with.