DFI LanParty UT nF4 SLI-DR - Your bios settings?

megalomando · 19-November-05, 09:21 PM

Hi,

Just got my rig running today and am not so familliar with the new bios options. I'd like to hear from someone with this board how they have their bios settings.

It'd probably save me a lot of grief if I could get some already working suggestions.

Thanks!

MM

$SOLID$ Necro · 25-November-05, 07:44 PM

Captain Planet was nice enough to write all of his memory settings down he used for the memory using BH-5, it's on the "Tight" side so you may have to loosen a few things, it's very similar to the settings I use.

Memory Voltage: 3.2

Command Per Clock (CPC) Enable
Cas Latency Control (Tcl) 2.0

Ras# to Cas# delay (Trcd) 2

Min Ras# active time (Trp) 2

Row Precharge time (TrP) 2

Row Cycle Time (TrC) 7

Row refresh cycle time (Trfc) 12

Row to Row delay (Trrd) 00

Write recover time (Twr) 02

Write to Read Delay (Twrt) 01

Read to Write Delay (Trwt) 02

Refresh period (Tref) 3120 cycles

Dram Bank Interleave: Enable

DQS Skew Control: Increase Skew

DQS Skew Value: 255

Dram Drive Strenght: Auto

Dram data drive strenght: Level 3

Max Async Latency: Auto

Dram Response time: fastest ( not sure if your bios has this)

Read Preamble time: Auto

Idle cycel limit: 016 cycles

Dynamic Counter: Enable

R/W Queuew Bypass: 16x

Bypass max: 07x

32 byte granularity: Auto ( Note: I disable it!)

In the thread below are screenshot for the settings I used at 3GHZ with an Opty 146.

http://forums.pcapex.com/showthread.php?t=57113

And here is a more "Generic" thread on the subject that covers TCCD based memory too.

http://forums.pcapex.com/showthread.php?t=56437

Cpt.Planet · 01-December-05, 01:30 PM

Quote:

Originally Posted by $SOLID$ Necro


	Captain Planet was nice enough to write all of his memory settings down he used for the memory using BH-5, it's on the "Tight" side so you may have to loosen a few things, it's very similar to the settings I use.

These are SUPER SUPER Tight and I doubt many could run these timings at those speeds.

jimbob · 05-December-05, 02:24 PM

http://www.dfi-street.com/forum/forumdisplay.php?f=38

Have a look on here. They don't have your exact memory type, but they've got settings for OCZ pc4000, so you should be able to tweak the settings for that to get it right for your ram.

I used a mixture between the DFI-street settings and the default ones, mainly cos i didn't like the idea of copy/pasting someones elses settings.

19-November-05, 09:21 PM		#1 (permalink)
megalomando Apex Techie Wannabe	DFI LanParty UT nF4 SLI-DR - Your bios settings? Hi, Just got my rig running today and am not so familliar with the new bios options. I'd like to hear from someone with this board how they have their bios settings. It'd probably save me a lot of grief if I could get some already working suggestions. Thanks! MM

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
AM2 BIOS settings..... explained	godfoot	AMD CPU/Motherboard OC	1	26-October-06 08:30 PM
Help with BIOS settings for OC my AMD 3000 64	killert	AMD CPU/Motherboard OC	17	19-July-06 03:15 AM
bios settings	intrigueme	AMD CPU/Motherboard OC	16	17-March-05 09:55 AM
What are the best bios settings for my system?	dr_paddo	Intel CPU/Motherboard OC	8	09-July-04 06:33 AM
XP2400 Bios Settings Help	dom6791	Motherboards / CPUs	3	11-February-03 04:13 PM

25-November-05, 07:44 PM		#2 (permalink)
$SOLID$ Necro Mastah Overclocker	Captain Planet was nice enough to write all of his memory settings down he used for the memory using BH-5, it's on the "Tight" side so you may have to loosen a few things, it's very similar to the settings I use. Memory Voltage: 3.2 Command Per Clock (CPC) Enable Cas Latency Control (Tcl) 2.0 Ras# to Cas# delay (Trcd) 2 Min Ras# active time (Trp) 2 Row Precharge time (TrP) 2 Row Cycle Time (TrC) 7 Row refresh cycle time (Trfc) 12 Row to Row delay (Trrd) 00 Write recover time (Twr) 02 Write to Read Delay (Twrt) 01 Read to Write Delay (Trwt) 02 Refresh period (Tref) 3120 cycles Dram Bank Interleave: Enable DQS Skew Control: Increase Skew DQS Skew Value: 255 Dram Drive Strenght: Auto Dram data drive strenght: Level 3 Max Async Latency: Auto Dram Response time: fastest ( not sure if your bios has this) Read Preamble time: Auto Idle cycel limit: 016 cycles Dynamic Counter: Enable R/W Queuew Bypass: 16x Bypass max: 07x 32 byte granularity: Auto ( Note: I disable it!) In the thread below are screenshot for the settings I used at 3GHZ with an Opty 146. http://forums.pcapex.com/showthread.php?t=57113 And here is a more "Generic" thread on the subject that covers TCCD based memory too. http://forums.pcapex.com/showthread.php?t=56437

05-December-05, 02:24 PM		#4 (permalink)
jimbob Apex Techie Lite	http://www.dfi-street.com/forum/forumdisplay.php?f=38 Have a look on here. They don't have your exact memory type, but they've got settings for OCZ pc4000, so you should be able to tweak the settings for that to get it right for your ram. I used a mixture between the DFI-street settings and the default ones, mainly cos i didn't like the idea of copy/pasting someones elses settings.