OCZ PC3200 VX, sure is fun to OC with!!

CPU Killer · 29-January-05, 08:25 PM

Attached pics speak for them selves...

Not too shabby for an CO stepping Proc. (3400 Clawhammer)

BigAkita · 29-January-05, 08:27 PM

You know what bro? I know they are putting out some good stuff lately, but I still have a hard time getting beyond their past.

MaTtsPc · 29-January-05, 09:16 PM

AMD'S just whoop A$$! My 2600M is still STUMPING them P4's.... LOL i do need some beter ram though.. but its on the way..

Matt

$SOLID$ Necro · 01-February-05, 08:00 PM

Oops! missed this thread...

Great timings at 250FSB, BH-5 numbers without shopping on EBAY!

Did you ever find out what the max FSB is with relaxed timings?

What voltage were you using? what is the have you tested them with?

CPU Killer · 01-February-05, 08:30 PM

Quote:

Originally Posted by $SOLID$ Necro


	Oops! missed this thread... Great timings at 250FSB, BH-5 numbers without shopping on EBAY! Did you ever find out what the max FSB is with relaxed timings? What voltage were you using? what is the have you tested them with?

So far I have only been running them @ 260x10 I was going for the most mhz with the 2-2-2-5-2 timings. To do this I had to run a beta bios on my UT250GB that allows you to up the vdimm. Then I tweaked the pots on my OCZ psu to give me up to 3.6 volts on the 3.3 rail. But I have only been running 3.3 volts to the memory to keep her stable at these timings. Over at DFI-Street.com there are a few people running VX with very tight timings at higher HTT. I would if I could, my old cpu can't handle it (shoddy mem controller). I am not too concerned about going any faster on this UT250GB.

I have some PC4200EL (ocz) to go into my NF4-sli mobo. I will be running at a min. of 300htt. I have confirmed these speeds on a couple of peoples DFI N4 mobos. One was running a 3200 (939, 90nm) @ 310x8 and another was running his 3500 (939, 90nm) @ 300x9. Both were using the same ram with the same timings. I have it all in place, I will be assembling the rig very very soon. Just needs to set aside some "alone" time to get down and dirty with the new toys.... BTW, to start out I will be running a 3500 then moving into the FX-55. I wanted to compare the 2 cpus to each other at overclock speeds and performance.

See ya'll soon with some data.

SpikeShot · 01-February-05, 09:48 PM

Well I got my 3000+ 90nm to 310X9 (and it was benchable) on air, so lets see what you can do with all that water. Look forward to seeing it.

I can't wait to get my board back from the old RMA department because I am going to be throwing phase into the mix and then we will see if it will go to 3.0 gigs. I may just need that 3500+ of yours to do it...if you like the FX-55 (you should love it btw) and want/need a buyer for the 3500+ I may take you up on an offer.

Ok, have fun over there with all that "free" stuff! Lucky dogg!

CPU Killer · 01-February-05, 11:31 PM

Quote:

Originally Posted by SpikeShot


	Well I got my 3000+ 90nm to 310X9 (and it was benchable) on air, so lets see what you can do with all that water. Look forward to seeing it. I can't wait to get my board back from the old RMA department because I am going to be throwing phase into the mix and then we will see if it will go to 3.0 gigs. I may just need that 3500+ of yours to do it...if you like the FX-55 (you should love it btw) and want/need a buyer for the 3500+ I may take you up on an offer. Ok, have fun over there with all that "free" stuff! Lucky dogg!

If I do sell it off (3500) I will PM ya 1st.

BTW, not everything is free, I did have to make my own waterblocks..... that cost me time.

29-January-05, 08:25 PM		#1 (permalink)
CPU Killer Apex Master Tech	OCZ PC3200 VX, sure is fun to OC with!! Attached pics speak for them selves... Not too shabby for an CO stepping Proc. (3400 Clawhammer) Attached Thumbnails

29-January-05, 09:16 PM		#3 (permalink)
MaTtsPc Apex Tech God	AMD'S just whoop A$$! My 2600M is still STUMPING them P4's.... LOL i do need some beter ram though.. but its on the way.. Matt Attached Thumbnails

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Best PC3200 2GB kit for OC?	TeamHype	Memory (RAM) OC	10	08-November-06 04:21 PM
OCZ 1GB (2x512MB) PC3200 DDR Kit $55	THRASHER2	Deals and Steals	0	03-April-06 07:25 PM
Ocz Pc3200	Fahye	Memory (RAM) OC	1	13-February-06 10:28 PM
2gb Pc3200 $99!!!!	pwrslyd	Deals and Steals	0	25-December-05 02:17 AM
what is the absolute best pc3200 ram out there???	justinvalencia	Other Hardware	5	31-May-03 04:20 PM

29-January-05, 08:27 PM		#2 (permalink)
BigAkita n00b-ass reviewer	You know what bro? I know they are putting out some good stuff lately, but I still have a hard time getting beyond their past.

01-February-05, 08:00 PM		#4 (permalink)
$SOLID$ Necro Mastah Overclocker	Oops! missed this thread... Great timings at 250FSB, BH-5 numbers without shopping on EBAY! Did you ever find out what the max FSB is with relaxed timings? What voltage were you using? what is the have you tested them with?

01-February-05, 09:48 PM		#6 (permalink)
SpikeShot Probationary User	Well I got my 3000+ 90nm to 310X9 (and it was benchable) on air, so lets see what you can do with all that water. Look forward to seeing it. I can't wait to get my board back from the old RMA department because I am going to be throwing phase into the mix and then we will see if it will go to 3.0 gigs. I may just need that 3500+ of yours to do it...if you like the FX-55 (you should love it btw) and want/need a buyer for the 3500+ I may take you up on an offer. Ok, have fun over there with all that "free" stuff! Lucky dogg!